Fullscreen
Loading...
 

System Workbench for STM32 Help

Forums » System Workbench for STM32» elf File not valid» elf File not valid
You are viewing a reply to elf File not valid Print this page only Print all pages

elf File not valid

Hm,
thx for your replay. I checked the eclipse run configurations and there is no difference between a working project and a non working project. Or is there an other place to check the Debugging configurations?


btw this is the Log for a working project, they almost look the same to me (except the last line of course)

Open On-Chip Debugger 0.10.0-dev-00274-g2ee83e0 (2017-01-12-17:09)
Licensed under GNU GPL v2
For bug reports, read
http://openocd.org/doc/doxygen/bugs.html
Info : auto-selecting first available session transport "hla_swd". To override use 'transport select '.
Info : The selected transport took over low-level target control. The results might differ compared to plain JTAG/SWD
adapter speed: 2000 kHz
adapter_nsrst_delay: 100
srst_only separate srst_nogate srst_open_drain connect_assert_srst
srst_only separate srst_nogate srst_open_drain connect_assert_srst
Info : Unable to match requested speed 2000 kHz, using 1800 kHz
Info : Unable to match requested speed 2000 kHz, using 1800 kHz
Info : clock speed 1800 kHz
Info : STLINK v2 JTAG v25 API v2 M v14 VID 0x0483 PID 0x374B
Info : using stlink api v2
Info : Target voltage: 2.867916
Info : stm32f4x.cpu: hardware has 6 breakpoints, 4 watchpoints
Info : Unable to match requested speed 2000 kHz, using 1800 kHz
Info : Unable to match requested speed 2000 kHz, using 1800 kHz
adapter speed: 1800 kHz
stm32f4x.cpu: target state: halted
target halted due to debug-request, current mode: Thread
xPSR: 0x01000000 pc: 0x08000208 msp: 0x20030000
configuring PLL

    • Programming Started **

auto erase enabled
Info : device id = 0x20016419
Info : flash size = 2048kbytes
stm32f4x.cpu: target state: halted
target halted due to breakpoint, current mode: Thread
xPSR: 0x61000000 pc: 0x20000046 msp: 0x20030000
wrote 262144 bytes from file Debug/myhidt.elf in 7.473427s (34.255 KiB/s)

    • Programming Finished **
    • Verify Started **

stm32f4x.cpu: target state: halted
target halted due to breakpoint, current mode: Thread
xPSR: 0x61000000 pc: 0x2000002e msp: 0x20030000
stm32f4x.cpu: target state: halted
target halted due to breakpoint, current mode: Thread
xPSR: 0x61000000 pc: 0x2000002e msp: 0x20030000
verified 214292 bytes in 1.639094s (127.674 KiB/s)

    • Verified OK **
    • Resetting Target **

Info : Unable to match requested speed 2000 kHz, using 1800 kHz
Info : Unable to match requested speed 2000 kHz, using 1800 kHz
adapter speed: 1800 kHz
shutdown command invoked


I don't see any difference?


Show posts:
 

Newest Forum Posts

  1. Error in final launch sequence by judoka_acl, 12:18
  2. STM32469I mipi read funtion by jimmylee0407, 11:38
  3. multiple definition of g_pfnVectors by mike796, 2017-07-20 15:27
  4. PROGMEM equivalent by bugmenot, 2017-07-20 11:31
  5. multiple definition of g_pfnVectors by judoka_acl, 2017-07-19 10:20
  6. PROGMEM equivalent by straubm, 2017-07-18 18:55
  7. Breakpoint at the wrong line by Andrei from The Great White North, 2017-07-18 18:01
  8. Breakpoint at the wrong line by judoka_acl, 2017-07-18 09:14
  9. Breakpoint at the wrong line by judoka_acl, 2017-07-18 09:01
  10. Breakpoint at the wrong line by tang, 2017-07-17 17:22

Last-Modified Blogs