NUCLEO-L476RG - Error: Whole bank access must start at beginning of bank.
I have seen this error discussed in this community before, however I haven’t seen a solution posted. Does anyone know what is causing this error? I am using the NUCLEO-L476RG board.
The following is my log:
11:25:16 **** Programming project stm32L476xx_drivers2 on chip ****
“C:\Ac6\SystemWorkbench\plugins\fr.ac6.mcu.externaltools.openocd.win32_1.23.0.201904120827\tools\openocd\bin\openocd.exe” -f stm32.flash.4377737752302794891.cfg -s “C:\Users\Ganesh\Documents\Ganesh_Documents\IntroToEmbeddedSystems\UdemyCourse\OpenSTM32SystemWorkbench\Workspace\stm32L476xx_drivers2” -s “C:\Ac6\SystemWorkbench\plugins\fr.ac6.mcu.debug_2.5.0.201904120827\resources\openocd\st_scripts” -c “program Debug/stm32L476xx_drivers2.elf verify reset ” -c shutdown
Open On-Chip Debugger 0.10.0+dev-00021-g524e8c8 (2019-04-12-08:48)
Licensed under GNU GPL v2
For bug reports, read
http://openocd.org/doc/doxygen/bugs.html
srst_only separate srst_nogate srst_open_drain connect_assert_srst
Info : The selected transport took over low-level target control. The results might differ compared to plain JTAG/SWD
padded zone erase set to 1
adapter speed: 8000 kHz
adapter_nsrst_delay: 100
Info : clock speed 8000 kHz
Info : STLINK v2.1 JTAG v33 API v2 M25 VID 0x0483 PID 0x374B
Info : using stlink api v2
Info : Target voltage: 3.263810
Info : Unable to match requested speed 8000 kHz, using 4000 kHz
Info : Stlink adapter speed set to 4000 kHz
Info : STM32L476RGTx.cpu: hardware has 6 breakpoints, 4 watchpoints
Info : Listening on port 3333 for gdb connections
target halted due to debug-request, current mode: Thread
xPSR: 0x01000000 pc: 0x08000714 msp: 0x20018000
Info : Unable to match requested speed 8000 kHz, using 4000 kHz
Info : Stlink adapter speed set to 4000 kHz
Info : Unable to match requested speed 8000 kHz, using 4000 kHz
adapter speed: 4000 kHz
- Programming Started **
auto erase enabled
Info : Device id = 0x10076415
Info : STM32L4xx flash size is 1024kb, base address is 0x8000000
Info : Erase the padded zone before the write
Error: Whole bank access must start at beginning of bank.
target halted due to breakpoint, current mode: Thread
xPSR: 0x61000000 pc: 0x20000050 msp: 0x20018000
wrote 4096 bytes from file Debug/stm32L476xx_drivers2.elf in 0.320144s (12.494 KiB/s)
- Programming Finished **
- Verify Started **
target halted due to breakpoint, current mode: Thread
xPSR: 0x61000000 pc: 0x2000002e msp: 0x20018000
target halted due to breakpoint, current mode: Thread
xPSR: 0x61000000 pc: 0x2000002e msp: 0x20018000
verified 3520 bytes in 0.210437s (16.335 KiB/s)
- Verified OK **
- Resetting Target **
shutdown command invoked
11:25:19 Build Finished (took 2s.341ms)
;){kind=link}