Loading...
 

SW4STM32 and SW4Linux fully supports the STM32MP1 asymmetric multicore Cortex/A7+M4 MPUs

   With System Workbench for Linux, Embedded Linux on the STM32MP1 family of MPUs from ST was never as simple to build and maintain, even for newcomers in the Linux world.
And, if you install System Workbench for Linux in System Workbench for STM32 you can seamlessly develop and debug asymmetric applications running partly on Linux, partly on the Cortex-M4.
You can get more information from the ac6-tools website and download two short videos (registration required) highlighting:

System Workbench for STM32


You are viewing a reply to problem with target programming  

run project

hello,
I can compile a project, but when I run it I get the message bellow, is it normal?
thank

Open On-Chip Debugger 0.10.0-dev-00011-g46c94c8 (2018-09-06-08:44)
Licensed under GNU GPL v2
For bug reports, read
http://openocd.org/doc/doxygen/bugs.html
srst_only separate srst_nogate srst_open_drain connect_assert_srst
Info : The selected transport took over low-level target control. The results might differ compared to plain JTAG/SWD
adapter_nsrst_delay: 100
adapter speed: 240 kHz
Info : clock speed 240 kHz
Info : STLINK v2.1 JTAG v28 API v2 M17 VID 0x0483 PID 0x374B
Info : using stlink api v2
Info : Target voltage: 3.283124
Info : Stlink adapter speed set to 240 kHz
Info : STM32L152RETx.cpu: hardware has 6 breakpoints, 4 watchpoints
Info : Stlink adapter speed set to 240 kHz
adapter speed: 240 kHz
target halted due to debug-request, current mode: Thread
xPSR: 0x01000000 pc: 0x08000230 msp: 0x20014000
STM32L: Enabling HSI
Info : Stlink adapter speed set to 4000 kHz
adapter speed: 4000 kHz

    • Programming Started **

auto erase enabled
Info : Device: STM32L1xx (Cat.5/Cat.6)
Info : STM32L flash has dual banks. Bank (0) size is 256kb, base address is 0x8000000
target halted due to breakpoint, current mode: Thread
xPSR: 0x61000000 pc: 0x2000000e msp: 0x20014000
wrote 4096 bytes from file Debug/test.elf in 0.228703s (17.490 KiB/s)

    • Programming Finished **
    • Verify Started **

target halted due to breakpoint, current mode: Thread
xPSR: 0x61000000 pc: 0x2000002e msp: 0x20014000
target halted due to breakpoint, current mode: Thread
xPSR: 0x61000000 pc: 0x2000002e msp: 0x20014000
verified 2100 bytes in 0.034671s (59.150 KiB/s)

    • Verified OK **
    • Resetting Target **

Info : Stlink adapter speed set to 240 kHz
adapter speed: 240 kHz
shutdown command invoked

 

Newest Forum Posts

  1. STM32429I_Discovery board with printf float support problem by johannes.visser@msc-technologies.eu, 16:08
  2. malloc heap issue with CubeMX Project by johannes.visser@msc-technologies.eu, 16:04
  3. Debugger not working by Daniel Jack Morley, 2019-11-27 21:46
  4. Compiler change problem by Lucian Pop, 2019-11-20 17:41
  5. Sample programs and compiling by jjtimer, 2019-11-20 10:31
  6. Unit test issues for STM32 by Rinkedevries, 2019-11-18 10:32
  7. Ubuntu 19.04 Debug problems by costantino, 2019-11-17 19:17
  8. Compile without eclipse by JSStabl, 2019-11-14 15:55
  9. Problem with PWM signal by ElectroniK, 2019-11-13 20:55
  10. Does System Workbench for STM32 work on a Raspberry Pi 4? by betocool, 2019-11-10 05:27

Last-Modified Blogs